Aerobed Premier Comfort Plus User Manual

Browse online or download User Manual for Furniture Aerobed Premier Comfort Plus. AeroBed Premier Comfort Plus User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
DEFLATION AND STORAGE
1. To deflate your AeroBed, press the deflate button on the control wand. Deflation takes approximately 60 seconds.
2. Roll or fold the AC cord with wand controller and secure it. Fold sides of bed into the center along its length. Tightly roll your
AeroBed around the pump. When the bed is completely rolled, place it into the lightweight duffel bag for storage.
3. Store your AeroBed in a clean dry place at room temperature (above 50°F/10°C). Storing your AeroBed under 50°F (10°C)
and over 100°F (38°C) may affect its performance and will not be covered under warranty.
CARE AND MAINTENANCE
1. Inspect your AeroBed prior to each use.
2. Keep your AeroBed away from any sharp objects. Large cuts or snags may not be repairable and will not be covered by your
warranty.
3. When not in use, store your AeroBed in a clean, dry place out of extreme temperatures. Product must be at room temperature
4. Do not store your AeroBed folded inside sofa beds or roll-aways. This may cause damage to your bed and will void your
prior to inflating.
5. In case of incidental damage to your bed, a repair patch has been included. Please follow repair instructions carefully.
Thank you for joining the AeroBed
®
family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination
from every AeroBed product. You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety,
care, and maintenance instructions for your new AeroBed product. Always instruct and supervise others on your bed’s proper use, maintenance, and
safety.
7972 Rev 01/08
Pump 111
Instruction Manual
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
Remove your AeroBed from its lightweight duffle bag. Keep bag for storage.
1. Place your rolled-up bed on the floor free of obstructions or sharp objects.
2. Remove AC plug, cord, and One Touch
®
Comfort Control Wand from plastic bag and shrink wrap.
3. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating: 120 VAC 60HZ 1.25A (Note:
230VAC product sold outside of North America). This product has a polarized attachment plug (one blade is wider than the
other) as a safety feature. This plug will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless the plug can be fully
inserted. Do not attempt to defeat this safety feature.
4. Push and hold inflate button on the control wand for approximately 60 seconds to inflate your AeroBed to the full (firmest)
capacity. Bed will not over-inflate.
5. Lie on the bed and use the control wand to adjust the firmness to your desired level. For firmer bed, press inflate button.
For a softer bed, press the adjust button.
CAUTION: Do not sleep on edges of the bed. Edges are less supportive and may crush under weight.
IMPORTANT SAFETY INFORMATION AND WARNINGS
WARNING: Adult supervision required for inflation, deflation, and maintenance. Follow all safety instructions to avoid serious injury.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where small children
can reach it. Do not use in or around water.
WARNING: Product is for indoor use only.
WARNING: For household / residential use only.
- This is not a water toy. Use as a mattress only.
- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress
and a wall.
- Remove all sharp objects from area where bed will be set up and used. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.
- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture the bed.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters,
open flame, or other hot objects.
- Unplug product when not in use.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously for more than 10 minutes. To avoid excessive heat build up in the pump, let it rest for 5 minutes between
complete inflation and deflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.
ADJUST
INF
L
A
T
E
DEF
L
A
T
E
ADJUST
INF L AT E
DEF L A
T E
ADJUST
INF
L
A
T
E
DEF
L
A
T
E
ADJUST
INF L
ATE
DEF L AT E
ADJUST
INF
L
A
T
E
DEF
L
A
T
E
ADJUST
INF
L
ATE
DEF L A
T E
IMPORTANT: PREPARATION OF YOUR AEROBED PRODUCT REQUIRES NO TOOLS. USE OF TOOLS MAY DAMAGE YOUR BED.
Page view 0
1 2

Summary of Contents

Page 1 - Instruction Manual

DEFLATION AND STORAGE1. To deflate your AeroBed, press the deflate button on the control wand. Deflation takes approximately 60 seconds.2. Roll or fol

Page 2 - CLEANING

CLEANINGWe recommend that you do not let the plush surface of your AeroBed® get wet. Repeated exposure to water or other liquids may cause damage to t

Comments to this Manuals

No comments